RPT - T300 Battery Regeneration

Product Description

RPTT300 Battery Condition Tester  Regeneration System

It is a very special allinone Battery Condition Tester for 6V12V leadacid batteries It supports multifunctions of digital Regenerator  Charger  Discharger  Power Supply  IR  CCA Checkers  Battery Condition Tester up to 300Ah at 12V batteries For 12V battery it is composed of 2 volts x 6 cells It is hard to know about shorted circuit cell cut cell corrosion state and any damaged cells prior to a restoration process In this reason the other competitors must check on these damaged cases after finishing a process only So we have developed on RPTT300 It can find the short of electrodes and damaged cells within few minutes before restoration procedure Auto battery condition test function whether to be restored or not  by CONDITION TEST mode By using it most batteries will be assorted for targeting ones to be regenerated with our new RPTT300 if they do not have any cell cut or short and internal cells damage corrosion RPTT300 has a full automated function to regenerate by setting of Voltage and Total capacity only

Multifunctional Modes 7in1 6V12V 40Ah300Ah

• Battery Regenerator at REGENERATION mode For 6V12V Battery up to 300Ah
• Battery Charger at CHARGE mode For 6V12V Battery only up to 300Ah
• Power Supply at POWER SUPPLY mode For 6V12V Battery up to 300Ah
• Manual setting mode of Voltage Current  Time for special  sleeping batteries
• Battery Discharger 420 Watts at DISCHARGE mode For 6V12V Battery up to 300Ah
• Battery Condition Tester at CONDITION TEST mode For 12V Battery only up to 200Ah
• IR Internal Resistance Checking  before  after 2 ways
• CCA Clod Cranking Ampere for Car Battery ONLY Checking  before  after 2 ways

Maximum Limited Output Current  6V12V  25A

• A serial connection up to 6V x 2 or 2V x 6 12V batteries at the same time up to 300Ah only
• The unique battery condition tester whether to be regenerated or wasted
• It takes 110 minutes for 12V battery condition test by RPTT300
• GOOD or BAD batteries will be tested  identified by RPTT300
• Please note that Battery Condition Test of RPTT300 is not an absoluteidentification method
• It will be an assistance mode to assort GOOD or BAD batteries in a short time  The Condition Test and IR  CCA will be for the reference only

RPTT300 is not an analyzer but a battery condition tester with Regenerator  Charger  Power Supply  Discharger  5 machines and 2 checker functions are allinone combined for 6V12V batteries At CONDITION TEST mode it can test the battery conditions 12V up to 200Ah within a few minute You can see it as CELL CUT CELL SHORT or CELL CORROSION on the screen with a beep sound If the battery is tested as a good battery to be regenerated then you can see OK TEST FINISH on the screen with a beep sound as well With RPTT300 you can regenerate all kinds of leadacid batteries including 6V12V VRLA AGM  GEL Car Deep Cycle Solar and so on The discharger supports up to 420 watts Input AC Power Consumption 550Watts max 280mmH x 430mmW x 520mmD 132kg 

Why used leadacid batteries need PRIME Battery Condition Tester RPTT300

Many used batteries have not good conditions therefore most used batteries should be tested on the inside cell conditions 2V x 6 cells  one 12V battery With any battery tester it is impossible to check that any 2V cell was already damaged among 6 cells 12V If any 2V cell was already damaged among 6 cells the whole 12V battery should be discarded Without RPTT300 nobody knows until finishing a regeneration process whether the battery was already damaged or not So you will waste much time labor cost and electricity uselessly If you have PRIME RPTT300 you can test all used 12V battery conditions prior to any process whether the battery condition is good to be regenerated or bad to be wasted  This is the only way to save time labor cost electricity cost and so on