Regenerator RPT-T300

• Battery Regenerator at REGENERATION mode For 6V12V Battery up to 300Ah
• Battery Charger at CHARGE mode For 6V12V Battery only up to 300Ah
• Power Supply at POWER SUPPLY mode For 6V12V Battery up to 300Ah
• Manual setting mode of Voltage Current  Time for special  sleeping batteries
• Battery Discharger 420 Watts at DISCHARGE mode For 6V12V Battery up to 300Ah
• Battery Condition Tester at CONDITION TEST mode For 12V Battery only up to 200Ah
• IR Internal Resistance Checking  before  after 2 ways
• CCA Clod Cranking Ampere for Car Battery ONLY Checking  before  after 2 ways

 Maximum Limited Output Current  6V12V  25A

• The unique battery condition tester whether to be regenerated or wasted
• It takes 110 minutes for 12V battery condition test by RPTT300
• GOOD or BAD batteries will be tested  identified by RPTT300
• Please note that Battery Condition Test of RPTT300 is not an absoluteidentification method
• It will be an assistance mode to assort GOOD or BAD batteries in a short time  The Condition Test and IR  CCA will be for the reference only
• GOOD  Not physically damaged and Capacity 30100 can be recovered
• BAD  Physically damaged as a disposal state and Capacity less than 30  Not to be recovered

RPTT300 is not an analyzer but a battery condition tester with Regenerator  Charger  Power Supply  Discharger  5 machines and 2 checker functions are allinone combined for 6V12V batteries At CONDITION TEST mode it can test the battery conditions 12V up to 200Ah within a few minute You can see it as CELL CUT CELL SHORT or CELL CORROSION on the screen with a beep sound If the battery is tested as a good battery to be regenerated then you can see OK TEST FINISH on the screen with a beep sound as well With RPTT300 you can regenerate all kinds of leadacid batteries including 6V12V VRLA AGM  GEL Car Deep Cycle Solar and so on The discharger supports up to 420 watts Input AC Power Consumption 550Watts max 280mmH x 430mmW x 520mmD 132kg

Why used leadacid batteries need PRIME Battery Condition Tester RPTT300

Many used batteries have not good conditions therefore most used batteries should be tested on the inside cell conditions 2V x 6 cells  one 12V battery With any battery tester it is impossible to check that any 2V cell was already damaged among 6 cells 12V If any 2V cell was already damaged among 6 cells the whole 12V battery should be discarded Without RPTT300 nobody knows until finishing a regeneration process whether the battery was already damaged or not So you will waste much time labor cost and electricity uselessly If you have PRIME RPTT300 you can test all used 12V battery conditions prior to any process whether the battery condition is good to be regenerated or bad to be wasted  This is the only way to save time labor cost electricity cost and so on

PRIME Battery Regeneration technology is the worlds first invention to remove hardened sulphates by real highfrequency pulse And it is far beyond other existing battery regeneration technologies Youll prove clearly when you try PRIME

Please check corrosion state inside the lead plates and lack of electrolyte in any cell total 6 cells in a battery In order to ascertain whether it is true you can try to open all cells in a battery and check whether any cell is damaged by lack of electrolyte and corrosion or not If the battery capacity after regeneration and discharge is lower than 30 our PRIME Battery Condition Tester RPTT300 is identified as a disposal corrosion or cellcut or cellshort So even though you found it as working but regeneration fails but the realistic life of batteries are almost finished about to die It means that the regenerable judgment of identification with RPTT300 will be over 30 of battery capacity therefore it identified that less than 30 capacity ranked battery is almost useless Even over 30 3170 rated with OK TEST FINISH with T300s Condition Test but it is not meaning of all good batteries The exact capacity will be identified after regeneration and discharge test only